Crestron CNWM-LU12 Guide d'installation Page 5
- Page / 12
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CDI-S100 Installation Guide v1.0 5
Baud Rate
Jumpers J1 to J3 set the serial port’s baud rate.
The default setting is 9600 baud. Check the
baud rate of the controlling equipment. If a
different baud rate is required, set the jumpers
according to the diagram below:
DEFAULT
SETTING
9600 baud
J1 J2 J3 J1 J2 J3
J1 J2 J3 J1 J2 J3
J1 J2 J3
4800 baud
1200 baud2400 baud
300 baud
Handshaking
RS-232C serial communication between
equipment sometimes requires ow
control (or “handshaking”), to conrm that
transmitter (the controller) and receiver
(the CDI-S100 in this case) are correctly
synchronised. PCB jumpers J4 and J5 control
handshaking.
Handshaking may be via “hardware”,
“software”, or off. Hardware handshaking
is also referred to as “RTS/CTS”, and needs
additional pins of the 9-pin serial connector
to be wired (see “Pinout” on page 7).
Software handshaking is also referred to as
“Xon/Xoff”.
The default setting is off (no handshaking).
If the controlling equipment requires
handshaking, set the jumpers according to the
following illustration:
Mechanical tting and internal
connection
If retrotting the CDI-S100 to an existing
CX462 installation, turn the CX462 off,
remove its IEC mains lead and all its other rear
panel connections (marking as necessary to
assist re-connection). If the CX462 is mounted
in a rack, remove it.
If tting the CDI-S100 to a new CX462,
unpack the CX462.
In either case, place the CX462 on a at
surface, with the rear of the unit facing you.
1. Undo the six screws securing the top
panel of the CX462; remove the panel.
Retain the screws.
2. Remove the plastic blanking plate which
covers the serial interface module
connector hole in the rear panel. This is
held in place with adhesive and can be
prised off.
3. Identify the empty 16-pin header labelled
CON7 on the main PCB just behind the
empty serial connector hole. Note there
is an M3 screw immediately behind this
connector, and another about 40 mm to
the right. Both these screws are clearly
marked with arrows; remove and retain
them.
- CDI-S100 1
- Contents 3
- Conguring the CDI-S100 4
- Introduction 4
- Scope of this manual 4
- What’s in the box 4
- Installation 4
- 9600 baud. Check the 5
- REMOTE TYPE 6
- LOCAL/REMOTE button 6
- REMOTE (with the LED on) 6
- CDI-S100 Remote Control 7
- Port parameters 7
- Examples: 8
- 5. Set master mic level 10
- APPENDIX 11
- Cable lengths 11
Produits connexes et manuels pour Non Crestron CNWM-LU12
Non Crestron WMKM-4L Manuel d'utilisateur
(16 pages)
(16 pages)
Non Crestron CP3 Manuel d'utilisateur
(5 pages)
(5 pages)
Non Crestron BB-4000L Manuel d'utilisateur
(12 pages)
(12 pages)
Non Crestron CNXLIR Spécifications
(16 pages)
(16 pages)
Non Crestron CT-3500 Spécifications
(14 pages)
(14 pages)
Non Crestron MMK-2000L Manuel d'utilisateur
(12 pages)
(12 pages)
Non Crestron TPS-CBL-T Spécifications
(66 pages)
(66 pages)
Non Crestron CT-1000 Spécifications
(44 pages)
(44 pages)
Non Crestron TPS-3000L Spécifications
(56 pages)
(56 pages)
Non Crestron CNMSX-PRO Spécifications
(44 pages)
(44 pages)
Non Crestron CNRACKX Spécifications
(34 pages)
(34 pages)
Non Crestron C2IR-8 Manuel d'utilisateur
(16 pages)
(16 pages)
Non Crestron CLSI-C6M Spécifications
(4 pages)
(4 pages)
Non Crestron CT-1550 Spécifications
(32 pages)
(32 pages)
Non Crestron GLS-EM-MCU Spécifications
(24 pages)
(24 pages)
Non Crestron CNRACKX-DP Spécifications
(44 pages)
(44 pages)
Non Crestron CNXLIR Spécifications
(16 pages)
(16 pages)
Mytee M-3 manuali
Manuali dei proprietari e guide per l'utente per Aspirapolvere Mytee M-3.
We fornisce 1 manuali pdf Mytee M-3 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels