Crestron PSPHD Spécifications télécharger pdf (Page 2)

quickstart guide

PSPHD

www.crestron.com

888.273.7876 201.767.3400

change without notice.

For details, refer to the latest revision of the

PSPHD Operations Guide, Doc. 6837.

QUICKSTART DOC. 6911B (2027570, Sheet 1 of 2) 07.10

PROCISE

™

High Definition Professional Surround Sound Processor

All brand names, product names, and trademarks

are the property of their respective owners.

PSPHD

NETWORK SETUP

IP Address

[172] 032. 159. 122

None: No subwoofer is present in the room.

Single: The system uses a single subwoofer.

Dual Mono: The system uses two mono

subwoofers.

Dual Stereo: The system uses two stereo

subwoofers.

Dual Stereo with Single Mono: The system

uses two stereo subwoofers and one mono

subwoofer.

Triple Mono: The system uses three mono

subwoofers.

NETWORK SETUP

IP Address: 172.032.159.122

INSTALLER MENU

Audio Setup

Network Setup

Control Setup

About

Exit Installer mode

AUDIO SETUP

Speaker Impedance is 8 Ohms

AUDIO SETUP

Left, Right

AUDIO SETUP

Center Speaker: Yes

AUDIO SETUP

Subwoofers: Dual Mono

STANDBY

Selection

Knob

HOME

DISPLAY

MUTE

Volume

Control

INSTALLER MENU

Audio Setup

INSTALLER MENU

Audio Setup

PSPHD

Verify that power to the PSPHD is on. The unit first goes through an

internal startup procedure that takes about fifteen seconds.

When the left-hand display shows PSPHD, press and hold the HOME

and DISPLAY buttons at the same time for about five seconds to

enter the Installer Menu mode. This mode provides a series of menus

and sub-menus, shown to the right, that let you perform a first time

setup and select basic configuration options.

1. Perform the functions in the order listed in the menu.

2. Rotate the selection knob to highlight each function and setting;

press the knob to select it.

3. Follow the on-screen instructions for each function.

4. The HOME button always takes you back to the Installer menu.

Advanced setup information and operational details are covered in

the latest version of the PSPHD Operations Guide (Doc. 6837).

Installer Menu Mode

Left, Right: Audio separated into left and

right channels.

Left, Right, Surround Left, Surround Right:

Audio separated into 4-channel surround sound.

For use in a 5.x surround setup.

Left, Right, Surround Left, Surround Right,

Single Back: Audio separated into 5-channel

surround sound. For use in a 6.x surround setup.

Left, Right, Surround Left, Surround Right, Back

Left, Back Right: Audio separated into 6-channel

surround sound. For use in a 7.x surround setup.

(This is the default setting.)

Use the selection knob to

choose Yes or No.

Use the selection knob to choose from

among the following setups:

Use the selection knob to

choose 4 or 8 Ohms (default).

(Changing this setting will

change the meter display on

the front panel.)

Press the selection knob to enable

changes to the PSPHD IP address.

Rotate the selection knob to change

the first octet. Press the knob to accept

the change and move to the next octet.

Repeat for each octet. Alternatively,

you can use the Soft Keys to directly

select the octet(s) to be changed, then

rotate the selection knob to make the

change and press the knob to accept it.

Refer to

page 3

AUDIO SETUP

None

Use the selection knob to choose

from among the following arrangements:

AUDIO SETUP

Center Speaker

Yes No

AUDIO SETUP

Speaker Impedance

4 Ohm 8 Ohm

Soft

Buttons

AUDIO SETUP

Speakers: L,R,SL,SR,

AUDIO SETUP

Restore Defaults

Including Presets

Are You Sure?

Yes No

Use the selection knob to

choose Yes or No (default).

AUDIO SETUP

Back

Press the selection knob to

return to the Installer

menu.

Continued

on page 3

NETWORK SETUP

Pair Crestron Amplifier

Pairing the PSPHD and PROAMP Amplifier

Press the selection knob to open the Amplifier Pairing

Control. If the PSPHD has already been paired with a

PROAMP amplifier, the display will ask that you either

exit, clear the pairing information, or reconfigure the

PSPHD’s pairing information. Use the selection knob to

choose between:

Exit: Cancels the operation.

Clear: Clears the pairing information. Any time pairing

is cleared, the PSPHD reboots.

Reconfigure: Clears the pairing information and begins

the pairing process.

Use the selection knob to highlight the type of

connection between the PSPHD and the PROAMP

amplifier.

Network: The PSPHD is connected to a PROAMP over

a local area network.

If Network is selected, the PSPHD will search for

PROAMP amplifiers on the network. The front panel

LEDs of the PROAMP amplifiers will flash indicating

they can be paired with the PSPHD.

AMPLIFIER PAIRING

Crestron Amplifier Connection

Network Direct

NOTE: The PSPHD and PROAMP amplifier must be

set to the same connection type. For information on

setting the PROAMP amplifier’s connection type, refer

to the latest version of the PROAMP Operations Guide

(Doc. 6974 or Doc. 6976) which is available from the

Crestron website.

NOTE: If using the “Network” connection type, the

PSPHD and the PROAMP amplifier must be on the

same subnet.

NOTE: If changing the connection method, the

PSPHD will automatically reboot. The pairing

procedure must be completed after the PSPHD

reboots.

Unpairing the PSPHD and PROAMP Amplifier

NOTE: To unpair the PSPHD and the PROAMP

amplifier, you must clear the pairing information from

both devices.

From the PSPHD’s INSTALLER MENU/Network Setup

section, press the selection knob to open the

Amplifier Pairing Control.

If the PSPHD is already paired with the PROAMP

amplifier, the display will ask that you either exit, clear

the pairing information, or reconfigure the PSPHD’s

pairing information.

Use the selection knob to choose Clear. This clears

the pairing information from the PSPHD.

On the PROAMP amplifier, press and hold the front

panel RESET button while you cycle the unit’s power.

The front panel LEDs blink, indicating that the

PROAMP is unpaired.

While the LEDs are flashing, press the rear panel

OVERRIDE/SETUP button or the front panel RESET

button on the PROAMP amplifier you wish to pair.

If the OVERRIDE/SETUP or RESET button is not

pressed within two minutes, the display will return to the

Network Setup section.

When the PROAMP is paired, the PSPHD display will

read "PSPHD Has Successfully Been Paired With An

Amplifier. Press The Selection Knob To Exit." The pairing

process is complete once you exit the installer menu and

the PSPHD reboots.

Direct: The PSPHD is directly connected to a PROAMP

amplifier with an Ethernet cable.

When Direct is selected, the PSPHD reboots and is

immediately paired with the PROAMP. There is no need

to press any buttons.

1 2 3

Commentaires sur ces manuels

Pas de commentaire

Crestron PSPHD Spécifications Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio Crestron PSPHD